Just How to Install a Bathtub Yourself
Just How to Install a Bathtub Yourself
Blog Article
What are your concepts about How to Install a Bathtub Yourself?
Installing a bath tub isn't precisely brain surgery, however it does require strong plumbing, carpentry, as well as occasionally, tiling skills. Changing an old bath tub with a new one is additionally a moderately hard project. If the old bathtub is readily easily accessible, the task can move easily; if you have to open up a wall surface to eliminate the old bathtub and place the new tub, the job is a lot harder. In either situation, the task is within a home handyman's abilities, although you will certainly need an assistant to move out the old tub and also set in the brand-new one. Make sure you have certified yourself for the task and also are comfortable attempting it. As opposed to hiring a specialist to take control of a halfway-completed project, it is much better to take into consideration employing one before you start. Chances are you may need a specialist plumber to make tube links.
This post will certainly help you set up a brand-new bath tub in your bathroom if you have already gotten a brand-new tub and do not require to transform the arrangement of your previous supply of water pipes.
Your devices and also material checklist ought to make up the following:
Getting ready for the Setup
To start with, the sustaining structure supplied with the bath ought to be fitted (if needed) according to the manufacturer's instructions. Next, fit the taps or mixer to the tub. When suitable the faucet block, it is necessary to see to it that if the tap comes with a plastic washer, it is fitted between the bath and the taps. On a plastic bath, it is also sensible to fit a supporting plate under the taps system to avoid stress on the tub.
Fit the versatile tap ports to the bottom of the two taps utilizing 2 nuts as well as olives (in some cases provided with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet opening, and after that pass the electrical outlet with the hole in the bath. Use the nut supplied by the producer to fit the plug-hole. Examine the plug-hole outlet for an inlet on the side for the overflow pipe.
Next, fit the end of the flexible overflow pipeline to the overflow electrical outlet. Afterwards, screw the pipeline to the overflow face which must be fitted inside the bath. Ensure you utilize all of the provided washing machines.
Link the trap to the bottom of the waste outlet on the bathtub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, and also screw on the catch to the outlet. Attach all-time low of the overflow tube in a comparable manner.The bathroom must currently prepare to be fitted in its final position.
Removing Old Touches
If you require to change old faucets with brand-new ones as a part of your setup, after that the first thing you ought to do is detach the supply of water. After doing so, turn on the faucets to drain pipes any kind of water continuing to be in the system. The procedure of eliminating the existing taps can be quite problematic due to the limited accessibility that is usually the situation.
Utilize a basin wrench (crowsfoot spanner) or a faucet device to reverse the nut that links the supply pipes to the faucets. Have a towel prepared for the staying water that will come from the pipelines. When the supply pipes have been gotten rid of, utilize the exact same tool to loosen up the nut that holds the faucets onto the bath/basin. You will need to quit the solitary taps from transforming throughout this process. Once the faucets have actually been removed, the holes in the bath/basin will certainly need to be cleaned up of any old securing compound.
Before going on to fit the brand-new taps, contrast the pipeline connections on the old faucets to the new taps. If the old faucets are longer than the new taps, after that a shank adapter is required for the brand-new taps to fit.
Installing the Bath tub
Utilizing both wooden boards under its feet, place the bath tub in the needed position. The wood boards are useful in equally spreading out the weight of the bathtub over the location of the boards rather than concentrating all the weight onto 4 small factors.
The next objective is to guarantee that the bath tub is leveled all round. This can be accomplished by examining the spirit level and changing the feet on the bathtub up until the spirit level reviews level.
To mount taps, fit all-time low of the furthest versatile tap port to the appropriate supply pipeline by making a compression join; after that do the same for the other faucet.
Switch on the water and examine all joints and brand-new pipework for leaks as well as tighten them if essential. Fill up the bath tub and also inspect the overflow electrical outlet as well as the regular outlet for leakages.
Finally, take care of the bath paneling as defined in the producer's user's manual. Tiling as well as sealing around the bath tub ought to wait till the bathtub has actually been made use of at least once as this will resolve it right into its last position.
Fitting New Touches
If the tails of the brand-new taps are plastic, after that you will certainly require a plastic connector to avoid damage to the thread. One end of the connector fits on the plastic tail of the tap and also the various other end supplies a link to the existent supply pipes.
If you need to fit a monobloc, then you will need decreasing couplers, which connects the 10mm pipe of the monobloc to the standard 15mm supply pipeline.
Next off, place the faucet in the mounting opening in the bath/basin making certain that the washers remain in location in between the tap and also the sink. Secure the tap in position with the maker given backnut. As soon as the faucet is firmly in position, the supply pipelines can be attached to the tails of the faucets. The faucets can either be attached by utilizing corrugated copper piping or with regular faucet adapters. The previous kind must be linked to the tap ends first, tightening only by hand. The supply pipes can later be connected to the various other end. Tighten up both ends with a spanner after both ends have actually been connected.
Tiling Around the Tub
In the location where the bath meets the ceramic tile, it is necessary to seal the accompanies a silicone rubber caulking. This is very important as the fitting can relocate enough to fracture a stiff seal, creating the water to permeate the wall in between the bath and also the tiling, bring about difficulties with moisture as well as feasible leakages to the ceiling below.
You can pick from a selection of coloured sealants to assimilate your components and also installations. They are marketed in tubes and also cartridges, and can sealing spaces approximately a size of 3mm (1/8 inch). If you have a larger void to fill up, you can fill it with spins of soaked newspaper or soft rope. Bear in mind to always load the tub with water before sealing, to permit the motion experienced when the bathtub is in use. The sealer can fracture fairly very early if you do not take into consideration this movement prior to sealing.
Conversely, ceramic coving or quadrant tiles can be made use of to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use as well as cut to size, are also quickly available on the marketplace. It is advisable to fit the floor tiles using waterproof or waterproof sticky and cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
As a keen reader about A Step-by-Step Guide to Installing a Bathtub, I was thinking sharing that piece of content was a great idea. Make sure you take the time to share this article if you enjoyed reading it. Thank-you for taking the time to read it.
Get Your Estimate Now
Report this page